HOME › NEWS & RESOURCES

Resources

NEWS & RESOURCES
ARTICLE · Technical Article

Differences Between Fluorosilicone and Silicone Release Films

2026.10.19 | SYPAC Resource Center

Although both are called “release film,” fluorosilicone and silicone follow two different technical routes. Choosing the wrong one has direct consequences: at best, it cannot be peeled during processing and the adhesive surface is torn; at worst, the entire roll sticks permanently and is scrapped. Remember the difference in one sentence—silicone release film cannot be used with silicone adhesive tape, while fluorosilicone release film is made specifically for silicone adhesive tape. This article explains it clearly from three dimensions: principle, adhesive system matching, and cost.

1. Conclusion First: A Comparison Table

Comparison ItemFluorosilicone Release FilmSilicone Release Film
Release AgentFluorosilicone release agentsilicone (polysiloxane) release agent
Target Adhesive SystemSpecifically for silicone adhesive tape; compatible with platinum and BPO adhesive systemsConventional tapes such as acrylic and rubber-based
Can It Be Used with Silicone Adhesive Tape?Yes (this is the reason it exists)No—both are silicone-based and will attract each other and stick permanently
Release Force RangeAdjustable from light to heavy-side releaseWide adjustable release force range
Silicone Transfer RiskSuitable for processes where silicone contamination is a concernPotential silicone transfer; residual adhesion rate must be evaluated
Typical ApplicationsOCA optical adhesive, medical silicone, semiconductor packaging, thermally conductive siliconePressure-sensitive labels, double-sided tape, foam tape, carrier film

※ Release force values are subject to their respective test conditions; physical property values are typical values and not guaranteed.

2. Principle Difference: Why silicone Film Cannot Be Used with Silicone Adhesive Tape

The role of release film is to “stay in place and peel off cleanly”; the key is that the interface between the release agent and the adhesive surface must be non-affinitive while still allowing stable separation.

  • The release layer of silicone release film is silicone (polysiloxane). When the adhesive surface is also silicone, the “silicone-to-silicone” affinity is extremely strong, and the two entangle—when peeling, it is not a matter of high release force; they simply cannot be separated, the adhesive surface is torn, and even the entire roll may be scrapped.
  • Fluorosilicone release film coats a fluorosilicone release agent on the PET substrate surface. Fluorosilicone has extremely low surface energy and “neither sticks to nor entangles with” silicone adhesive surfaces, so it peels stably and is the designated partner for silicone adhesive tape.
Selection iron rule: As long as your adhesive system is silicone (thermally conductive silicone pads, silicone foam, silicone pressure-sensitive adhesives, etc.), fluorosilicone release film is the best choice; conversely, conventional acrylic adhesive systems can simply use silicone film.

3. When Fluorosilicone Must Be Used

  • Thermally conductive silicone: Thermally conductive pads are mostly silicone-based (SRF08 is the best choice, designed specifically for thermally conductive silicone).
  • Silicone foam: Foamed silicone rubber has weak adhesive tack and is prone to delamination, requiring heavier-side release force (e.g., FL186, which does not delaminate during use).
  • Medical tape: High requirements for cleanliness and peel stability; fluorosilicone film has low silicone transfer and good batch consistency (e.g., FL160H).
  • Die-cutting of silicone pressure-sensitive adhesive tape: Compatible with both platinum and BPO adhesive systems; select release force according to the process.

4. When silicone Film Is Sufficient

  • Acrylic adhesive tape: The mainstream adhesive system for labels, double-sided tape, and protective film; mature matching with silicone release film and cost-effective.
  • Rubber-based adhesive tape: silicone film is also suitable.
If the adhesive surface will later be printed, coated, or laminated, remember to also confirm the residual adhesion rate during selection—if silicone transfer from the silicone film exceeds the limit, it will reduce the tape’s actual adhesion.

5. Three Common Misconceptions

  • Misconception 1: Fluorosilicone is “more advanced” than silicone, so always use fluorosilicone. In fact, the release solution should depend on the adhesive system and application scenario.
  • Misconception 2: Try silicone film first. For silicone adhesive tape, there is no “try it and see”—once silicone meets silicone and is laminated, it sticks permanently, resulting in direct loss of samples and labor hours.
  • Misconception 3: Look only at the release force number. Peel stability (batch consistency) and silicone transfer often affect yield more than nominal release force, especially in automated film-peeling processes.

6. Not Sure About the Adhesive System? Confirm Before Ordering

Many sites are not sure of the exact adhesive system of their tape. We recommend sending us a sample first so we can identify the adhesive system, then matching the release solution and providing samples accordingly; this effectively avoids selection errors.

Need help with selection or requesting samples?
Welcome to contact the SYPAC sales team for technical data sheets (TDS) and samples. We will recommend the corresponding series and release force based on your adhesive system and process.

Kunshan · Dongguan · Taiwan · Vietnam | MATERIALS FOR A BETTER TOMORROW