ARTICLE · Technical Article
How to Choose the Release Force of Release Film?
2026.00.00 | SYPAC Resource Center
Release force is one of the most critical indicators of release film: it determines the feel and yield when tapes and adhesive materials are laminated and when the release film is peeled off. If selected too high, peeling becomes laborious and may lift the adhesive surface; if selected too low, the release film may detach prematurely during transport or processing. This article uses three steps to turn “how to choose release force” into a selection question with clear rules to follow.
1. First, Align the Terminology: What Release Force Is and How It Is Measured
Release force refers to the force required to peel the release film from the attached adhesive surface at a specific angle and speed. The smaller the value, the “lighter” it is. The common industry test condition is a 180° peel angle, with values expressed in grams (g). The catalog data for SYPAC’s fluorosilicone series is based on 180° testing; the non-silicone series uses Nitto 31B tape as the test reference.
Note: Release force has no absolute value—the same film will give different readings when tested with different tapes, different widths, and different speeds. Therefore, be sure to confirm the supplier’s test conditions during selection, and compare as much as possible using your own actual adhesive.
2. Three Steps to Lock In the Target Range
01First Look at the “Adhesive System”—It Determines Which Type of Release Film to Use
- Silicone adhesive tape: Fluorosilicone release film must be used. Silicone-oil-based release film is compatible with silicone adhesive systems and will stick permanently and cannot be peeled.
- Acrylic and rubber-based tapes: silicone, low-silicone, or non-silicone series can be selected; if the process is sensitive to silicone transfer (such as subsequent coating or printing), prioritize non-silicone release film.
- Low-adhesion tape and protective film: The non-silicone series is the standard choice.
02Next Look at the “Process”—It Determines Light, Medium, or Heavy
Within the same series, select from light to heavy release force. The principle is: the release film should stay in place when needed and peel smoothly when it is time to remove it.
- Light release: Suitable for automated film peeling, large-area removal, or cases where the adhesive surface has strong tack. Examples include die-cutting waste removal and thermally conductive silicone lamination.
- Medium release: The general range for coating and die-cutting, balancing storage stability and peeling feel.
- Heavy-side release: Suitable for cases where the adhesive surface has weak tack, or storage and transport conditions are harsh, or the release film must not loosen.
03Finally Look at “Who Peels It and How It Is Peeled”
- Manual film peeling: A lighter feel is friendlier, but also prevent it from being so light that it detaches by itself during handling.
- Automated equipment film peeling: Prioritize stable release force and batch consistency—fluctuation affects yield more than the absolute value.
- Die-cutting waste removal: Release force should match the die and waste removal speed. If waste removal is too fast, try one grade lighter.
3. Three Common Misconceptions
- Misconception 1: The lower the release force, the better. If too light, the release film may detach prematurely during slitting, storage, or transport, losing its protective purpose. Just enough is sufficient.
- Misconception 2: Looking only at factory data. Release force changes with storage time, temperature, and humidity. Retesting is recommended after high-temperature and high-humidity exposure.
- Misconception 3: Ignoring the residual adhesion rate. Even if release force meets specification, excessive silicone transfer will still reduce tape adhesion. For high-requirement applications such as medical and electronics, be sure to confirm the residual adhesion rate as well.
4. The Fastest Method: Request Samples and Test
Specification sheets can only help narrow the range; the final decision must be based on actual machine testing: run a trial with the tape you are currently using, your equipment, and your peeling speed. SYPAC performs precision coating in a cleanroom environment, with stable release force and batch consistency. The fluorosilicone series covers 1–25 g from light to heavy-side and can be adjusted according to requirements.
Need help with selection or requesting samples?
Welcome to contact the SYPAC sales team for technical data sheets (TDS) and samples. We will recommend the corresponding model based on your adhesive system and process.
Kunshan · Dongguan · Taiwan · Vietnam | MATERIALS FOR A BETTER TOMORROW